THE BEST GLIDER M A I D E N • Django Bubble Surfer by SANSIBEAR 🐻 • (English/Français 4K 60fps)

HONESTLY, THIS “DJANGO BS” IS THE BEST GLIDER I’VE EVER FLOWN AMONG ALL THE GLIDERS I’VE TESTED (F3J, F3K, F5J, F3B) 😳 #notsponsored
Get yours at https://sansibear.de/product/bubble-surfer-django-bs-rtf/

🇺🇸 Hi folks 👋🏻🤠

Thank you for watching this video and don’t forget to subscribe so you don’t miss anything (it’s free but it helps content creators a lot) 🙏🏻🥰

If you want to help me to expand my squadron 😜 or buy a specific plane to review, you can help me by making a small donation via my PayPal link https://www.paypal.me/arthurjanin?locale.x=fr_FR

Thank you very much in advance my friends 🤩🙏🏻

🇫🇷 Salut les copains 👋🏻🤠

Merci d’avoir regardé cette vidéo et n’oubliez pas de vous abonner pour ne rien manquer (c’est gratuit et pourtant ça aide énormément les créateurs de contenus) 🙏🏻🥰

Si vous voulez m’aider à agrandir mon escadron 😜 ou que j’achète un avion en particulier, vous pouvez m’aider en faisant un petit don via mon lien PayPal https://www.paypal.me/arthurjanin?locale.x=fr_FR

Merci beaucoup beaucoup d’avance les amis 🤩🙏🏻

📸 Follow me on Instagram : https://www.instagram.com/arthuraerorc
⏰ TikTok : https://vm.tiktok.com/ZMNYCqUhC/

You can buy my things here ⬇️

🎮 Jeti Rx and DS16 ➡️ https://www.opale-paramodels.com/fr/ @Opale Paramodels
🔋CNHL LiPo ➡️ https://chinahobbyline.com
✈️ Jets and more ➡️ https://www.turbines-rc.com/fr/?aff=4

🌪️ Bubble Surfer [Django BS] by SANSIBEAR 🐻

➡️ https://sansibear.de/product/bubble-surfer-django-bs-rtf/

Tail servos : 2 x KST X08
Wing servos : 4 x KST X06H
Fuselage : Cockpit and tail CFK (carbon)
Wings : Sandwich Carbon XPS (foam)

Wingspan (envergure) : 2540 même
Length (longueur) : 1375 même
Weight PNP (without Rx, LiPo) : 477gr
Weight RTF CG80mm with 2S 2000mAh (114gr) : 610gr

⚖️ Parts :
Wingspar + elevator screws : 9gr
Right wing (with 2 KST X06H) : 147gr
Left wing (with 2 KST X06H) : 143gr
Horizontal stab : 16gr
Fuselage (without Rx) : 162gr

Surface : 46,9 dm²
Wing load (Charge alaire) : 13 g/dm2 (CG 80mm 610gr)

📏 Settings (réglages, merci @Pierre Meunier 😅) :

Ailerons : 20mm down / 14mm up
Flaps (mix ailerons to flaps) : 10mm down / max flap can go up
Elevator : 7mm / 12mm
Rudder : 17mm

– Flaps offset : Speed 2mm up / normal 0 / thermal 0,5mm down
– Ailerons offset : Speed 2mm up / normal 0 / thermal 0
– Elevator offset : Speed 1mm down / normal 0 / thermal 0

Snap flaps : 2mm down flaps only
Thermal Flaps camber : 2mm/4mm max

– Brakes (Freins) : Flaps 90° / elevator compensation 7mm down
– Launch in speed mode with a Preset (like in F3K) : 1mm down elevator (on a momentary switch) like that the glider won’t climb too much when you throw it…

❌ Book CG : 80mm (LiPo 2S 2000mAh 114gr all the way forward) but CG 84mm (glider’s weight 602gr without lead on LiPo !!!)

Max limit average wind 12 km/h (7.5 mph), I won’t fly with more wind 😕

Flights :
– Maiden (filmed) : 10min flight : 8.10v left (for a 8.20v, 2S 2000mAh LiPo) 😂😳

0:00 Présentation française
0:39 English presentation
1:41 Rates / Flight modes (phases de vol) @Pierre Meunier callouts
4:26 CG 80mm
5:13 Antennas outside / Pegs to throw it
5:53 First launch (elevator not well centered 😕)
7:16 Not enough throws with 5mm…
7:46 Second flight
8:42 First thermal (INSANE)
9:22 Thermal mode test (flaps -0,5mm to be more touchy with thermals)
9:48 1st notch flaps (-2,5mm) CRAZY
10:19 Full flaps (-4,5mm flaps)
10:41 Speed mode test (had too much down offset elevator)
10:51 Normal mode (flaps, ailerons flush)
11:01 Thermal mode
11:20 Congrats @Sansi Bear
11:57 New offset for speed mode (only 2% down elevator, 1mm)
12:12 Brakes test (Finally I needed 7mm down elevator)
12:48 LANDING
13:02 First thoughts ❤️
14:00 Discussion about my channel
14:32 Please Subscribe 🙏🏻😍
14:54 Photos

#glider #rcplane #django #sansibear #hlg #f3k #f3j #jeti #radiocontrol #setup #modellbau #bubblesurfer #maiden #perfect #crash #new #rcglider

Bitte dieses Feld leer lassen

E-Mail-Adresse *

Vorname Nachname *

Wähle dein Newsletter, Du kannst es auch später anpassen.

Freitag um 18:00 täglich um 18:00 Uhr

Datenschutzerklärung

Gehe bitte in Dein E-Mail Postfach und bestätige mit dem Link. --- Please go to your e-mail inbox and confirm with the link. --- Veuillez vous rendre dans votre boîte de réception e-mail et confirmer avec le lien. --- Vaya a la bandeja de entrada de su correo electrónico y confirme con el enlace. --- Por favor, vá para a caixa de entrada do seu e-mail e confirme com o link.