Watch ALL the video to know all the clues !

🇺🇸 Hi folks 👋🏻🤠

Thank you for watching this video and don’t forget to subscribe so you don’t miss anything (it’s free but it helps content creators a lot) 🙏🏻🥰

If you want to help me to expand my squadron 😜 or buy a specific plane to review, you can help me by making a small donation via my PayPal link https://www.paypal.me/arthurjanin?locale.x=fr_FR

Thank you very much in advance my friends 🤩🙏🏻

🇫🇷 Salut les copains 👋🏻🤠

Merci d’avoir regardé cette vidéo et n’oubliez pas de vous abonner pour ne rien manquer (c’est gratuit et pourtant ça aide énormément les créateurs de contenus) 🙏🏻🥰

Si vous voulez m’aider à agrandir mon escadron 😜 ou que j’achète un avion en particulier, vous pouvez m’aider en faisant un petit don via mon lien PayPal https://www.paypal.me/arthurjanin?locale.x=fr_FR

Merci beaucoup beaucoup d’avance les amis 🤩🙏🏻

📸 Follow me on Instagram : https://www.instagram.com/arthuraerorc
⏰ TikTok : https://vm.tiktok.com/ZMNYCqUhC/

You can buy my things here ⬇️

💨 Kingtech Turbines ➡️ https://www.kingtechturbine.lu
🇺🇸 ⚓️ HSDJETS T-45 Turbine Ready ➡️ https://hsdjetsuk.com/product/t-45-goshawk-turbine-foam-jet-red-arrows-pnp-smoke-no-turbine/

🎮 Jeti Rx and DS16 ➡️ https://www.opale-paramodels.com/fr/ @Opale Paramodels
🔋CNHL LiPo ➡️ https://chinahobbyline.com
✈️ Jets and more ➡️ https://www.turbines-rc.com/fr/?aff=4

🇺🇸 ⚓️ HSDJETS T-45 Goshawk Turbine Foam Jet (PNP + Smoke, no turbine)

Wingspan 1502mm, length 1903mm, dry weight 7.7kg, flying weight 10,5kg (1800ml kero + 120ml UAT + 750ml smoke)
– Turbine : Kingtech 70G4+ ➡️ https://kingtechturbine.lu/KingTech-K70G4-_2
– Very hard foam (20 times EPO)
– Control system included MFC-2085
– 2 LiPo CNHL 2S 2200mah XT60 (required)
– With slats and air brakes

❌ Book CG 150mm from slat root leading edge, straight along fuselage and aligned with first wing screw!

📏 Rates after the 2nd flight (For the elevator, measure from the leading edge of the tail, centered with fuselage marks) : low / mid / high
– Elevator : 20/20/20mm (you have to change servo arm linkage to outermost hole ⚠️)
– Ailerons : 15/18/23mm
– Rudder : 25/30/40mm
– Flaps : 20 / 35mm (5mm up elevator)

MFC-2085 inputs:
R11 : slats
R13 : smoke pump
R14 : airbrakes

⏰ Flights with timers and voltage
1st (filmed) : 4m40 turbine and 50% fuel left (pump factor was 600 but totally wrong so I set at 400 after maiden)
2nd (filmed) : 3m18 turbine and 70% fuel left (I finally set pump factor at 350)

0:00 Présentation française
0:28 English presentation
1:00 MFC/GSU start
1:55 K70 Start-up 🔥
3:01 Take-Off
3:28 Trimming / increase elevator throws
4:47 Half throttle to full throttle climb out
5:07 Roll
5:25 Close flyby
5:37 Full flaps
5:48 Go around
6:13 Airbrakes deployed / Landing (full up elevator)
6:45 First thoughts
7:28 Telemetry check
8:13 Please Subscribe 🙏🏻😍
8:39 Elevator servo arm 😳
9:12 Details photos

#turbine #rcplane #kingtech #jet #jeti #opale #radiocontrol #setup #modellbau #t45 #eflite #new #hsdjets #perfect #foam #crash #fms #freewing